Nsi-industries DGLC Old Series Bedienungsanleitung PDF herunterladen

TORK MODEL DGLC

DIGITAL LIGHTING CONTROLLER

Installation & Operation

READ INSTRUCTIONS CAREFULLY BEFORE SETTING UNIT

PHOTOCELL MODEL EPC1 IS SUPPLIED WITH

THE DIGITAL TIME SWITCH

FEATURES

Single channel controller - 2 circuit

Circuit #1: Photocell ON/Time OFF/Time

ON/Photocell OFF, Selectable days

Circuit #2: Photocell ON/Photocell OFF, Everyday

7 day scheduling

Special day scheduling

32 set points

Battery back-up - uses standard 9 volt non-

rechargeable (not supplied). Lithium averages

275 hours of power outage; Alkaline averages

100 hours

Manual override to the next scheduled event

Automatic daylight saving - user selectable

Automatic leap year compensation

AM/PM or 24 Hour format - user selectable

INSTALLATION

UNIT IS TO BE INSTALLED BY A LICENSED ELECTRICIAN

1. Remove the photocell (EPC1) from the time

switch enclosure (lift insulating board at bottom).

2. To remove unit from enclosure: Push tab on

right to swing unit to the left and remove.

3. Mount the enclosure at eye level using screws

or other suitable fastening device. Bring supply

and load wires in through the bottom or side

knockouts. DO NOT USE TOP KNOCKOUTS.

Clock input wires to controller must be from a

dedicated source i.e. no other loads connect-

ed to the same circuit.

4. Install standard 9 volt lithium or alkaline battery

(not supplied) by gently squeezing the right

side of the battery cover on the front of unit

and pull to open. Pull out the battery connector

and connect the battery. Reinstall battery

cover. Lithium should be replaced every 3-5

years; alkaline every year.

NOTE:

Unit can also be programmed using bat-

tery power only.

5. Reinstall unit by reversing step # 1 above and

connect wires to unit as per suggested wiring

diagrams. See illustration on enclosure label.

6. The photocell can be mounted directly through

a standard 1/2” knockout. Connection to junc-

tion box must be watertight through a tapped

opening and the use of a nut and neoprene

washer to be provided by the installer. In addi-

tion, use suitable tape or sealant on nipple

threads. Mounting is recommended in the

upright position with cell facing North for

optimum efficiency.

Protect the window side of the photocell from

any direct artificial light that may be on after

dark, from windows, signs, and the artificial

light being controlled.

Locate the photocell in as open a spot as pos-

sible. Particularly keep it out of corners and

overhanging eaves.

Do not wire the photocell while AC current

is applied to the unit.

Do not apply any voltage from external

source to photocell input terminals.

PHOTOCELL INPUT

Connect Photocell (EPC1) to input terminals

labeled (1 & 2 ).

One photocell controls both circuits.

POTENTIOMETER:

Adjust potentiometer labeled (MIN MAX) for

desired light level actuation. If adjusted to the

extreme left (MIN position), the ON relay will close

1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1 - Installation & Operation

TORK MODEL DGLCDIGITAL LIGHTING CONTROLLERInstallation & OperationREAD INSTRUCTIONS CAREFULLY BEFORE SETTING UNITPHOTOCELL MODEL EPC1 IS SUPPLIED

Seite 2

TORK MODEL DGLCDIGITAL LIGHTING CONTROLLERInstallation & OperationREAD INSTRUCTIONS CAREFULLY BEFORE SETTING UNITPHOTOCELL MODEL EPC1 IS SUPPLIED

Seite 3 - MILITARY FORMAT:

at 1 to 2 footcandles. If adjusted to the extremeright (MAX position), the ON relay will close atapproximately 100 footcandles. (There is a 2 - 4secon

Seite 4

at 1 to 2 footcandles. If adjusted to the extremeright (MAX position), the ON relay will close atapproximately 100 footcandles. (There is a 2 - 4secon

Seite 5 - DAYLIGHT SAVING

Once the ENTER is pressed, unit goes to RUNmode. You can recognize that the unit is in theRUN mode when the real time (including sec-onds) is displaye

Seite 6

Once the ENTER is pressed, unit goes to RUNmode. You can recognize that the unit is in theRUN mode when the real time (including sec-onds) is displaye

Seite 7 - OVERRIDE (CIRCUIT #1 ONLY)

MO, TU, WE, TH, FR, SASU, MO, TU, WE, TH, FR, SAIndividual days: SU, MO, TU, WE, TH, FR, SA,and D for Special Day (usually a holiday).A special holida

Seite 8

MO, TU, WE, TH, FR, SASU, MO, TU, WE, TH, FR, SAIndividual days: SU, MO, TU, WE, TH, FR, SA,and D for Special Day (usually a holiday).A special holida

Kommentare zu diesen Handbüchern

Keine Kommentare

Nsi-industries DGLC Old Series Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Ausrüstung Nsi-industries DGLC Old Series herunter. NSi Industries DGLC Old Series User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Ausrüstung Nsi-industries DGLC Old Series