Nsi-industries DG120 Old Series Bedienungsanleitung PDF herunterladen

KEY FUNCTIONS

DAY/MONTH: Press to advance the day in the CLK

mode. Press to advance the Month in the DATE

mode.

HOUR/DATE: Press to set the Hours in the CLK

mode and in the Schedule SET mode. Press to

advance Date in the DATE mode.

MIN/YEAR: Press to set the Minute in the CLK mode

and in the Schedule SET mode. Press to advance

Year in the DATE mode.

OVERRIDE: Press to alter the Load status and/or to

Override scheduled event.

MODE: Press to advance to next mode without

affecting the scheduled memory information.

Sequence is: RUN, CLK, DATE, schedule SET. In

the SET mode, unit automatically reverts to the

RUN mode if no entries are made for 5 minutes.

SP DAY: Press during RUN mode to execute the

“SPECIAL DAY” schedule everyday. LCD will display

D in upper right corner. Pressing SP DAY again will

toggle the unit back to normal 7 day program opera-

tion.

ON/OFF: Pressing each time will select ON or OFF

event. Multiple OFFs may be scheduled to cancel

override ON’s.

ENTER: Press to store the displayed information into

memory. Information will not be stored until

ENTER is pressed.

NOTE: During settings, each press of the key will

advance one number. For rapid advance, hold key in.

DAY

MONTH

HOUR

DATE

MIN

YEAR

OVER-

RIDE

MODE

DAY

ON/

OFF

ENTER

TORK DG100 / DG120

DIGITAL TIME SWITCH

SEVEN DAY

READ INSTRUCTIONS CAREFULLY BEFORE SETTING UNIT

FEATURES

Single channel controller

7 day scheduling

Special day scheduling

32 set points

Battery back-up uses standard 9 volt non-recharge-

able (not supplied). Lithium averages 450 hours of

power outage; Alkaline averages 175 hours

Manual override to the next scheduled event

Automatic daylight saving - user selectable

Automatic leap year compensation

AM/PM or 24 hour format - user selectable

INSTALLATION

UNIT IS TO BE INSTALLED BY A LICENSED ELECTRICIAN

1. To remove unit from enclosure: Push tab on right

to swing unit to the left and remove.

2. Mount the enclosure at eye level using screws or

other suitable fastening device. Bring supply and

load wires in through bottom or side knockouts.

DO NOT USE TOP.

Input wires to controller must be dedicated i.e. no

other loads connected to the same circuit.

3. Install a standard 9 volt lithium or alkaline battery

(not supplied) by gently squeezing the right side of

the battery cover on the front of the unit and pull

to open. Pull out the battery connector and con-

nect the battery. Reinstall battery cover. Lithium

should be replaced every 3-5 years, Alkaline

every year.

NOTE: Unit can be fully programmed using battery

power only.

4. Reinstall unit by reversing step #1 above and con-

nect wires to unit as per suggested wiring dia-

grams. See illustration on enclosure label.

1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1 - SEVEN DAY

KEY FUNCTIONSDAY/MONTH: Press to advance the day in the CLKmode. Press to advance the Month in the DATEmode.HOUR/DATE: Press to set the Hours in the C

Seite 2

KEY FUNCTIONSDAY/MONTH: Press to advance the day in the CLKmode. Press to advance the Month in the DATEmode.HOUR/DATE: Press to set the Hours in the C

Seite 3

Press DAY/MONTH key to select today’s day. PressHOUR key to set present hour (check AM/PM). PressMIN key to set present minute. Press ENTER key. Unitn

Seite 4

Press DAY/MONTH key to select today’s day. PressHOUR key to set present hour (check AM/PM). PressMIN key to set present minute. Press ENTER key. Unitn

Seite 5 - TO SET SCHEDULE

SPECIAL DAY (HOLIDAY)To execute this schedule at any time, simply pressthe SP DAY key while the unit is in the RUN mode.A letter “D” will appear in th

Seite 6

SPECIAL DAY (HOLIDAY)To execute this schedule at any time, simply pressthe SP DAY key while the unit is in the RUN mode.A letter “D” will appear in th

Seite 7 - OVERRIDE

DELETE: If you choose to delete a schedule, simplymodify the HOURS and MINUTES, until the time dis-play reads --:--. This will occur after scrolling p

Seite 8

DELETE: If you choose to delete a schedule, simplymodify the HOURS and MINUTES, until the time dis-play reads --:--. This will occur after scrolling p